|
Input section |
Applicable sensor
(sold separately) |
IP-292/296, IP-3000A/3100, OM-1200/1500, VP-202/1220, LG-9200, MP-900/9000 series, MP-981, EXT(PULSE), ECU crank angle signal(option) |
|
Measurement range |
IP-292/296/3000A/3100:120 to 20000 r/min
OM-1200/1500:120 to 20000 r/min
VP-202/1220:120 to 20000 r/min
MP-900/9000 series:30 to 99999 r/min
MP-981:0 to 99999 r/min
LG-9200:0 to 99999 r/min
EXT(PULSE):0 to 99999 r/min
CRANK PULSE:120 to 20000 r/min |
|
Input frequency range |
0.1 Hz - 120 kHz *1 |
|
Display |
Display method
(display size) |
Fluorescent display tube (52.5 x 11.5 mm) |
|
Display range |
0 to 99999 r/min *1 |
|
Accuracy |
±0.01 %/F.S(±1 count)or less |
|
Analog output |
|
Output range |
0 to 10 V |
|
Range setting |
1 to 99999 r/min(set in steps of 1 r/min) |
|
Load resistance |
100 kΩ or more |
|
Response |
Updates in less than 8µs after cycle becomes stable. |
|
Resolution |
16 bit |
|
Pulse output |
Output item
(selectable) |
DIRECT : Wave-shaped output
0.5[P/R] : Output r/min value to obtain 0.5 P/R
1[P/R] : Output r/min value to obtain
1 P/R 60[P/R] : Manually switch r/min value output to obtain 60 P/R |
|
Signal level |
0-5 V logic signal(Lo:0.4 V or less, Hi:4.5 V or less) |
|
Load resistance |
100 kΩ or more |
|
Contact output |
|
Item |
Engine run, over run |
|
Setting range |
1 to 99999 r/min |
|
Contact capacity |
DC 30 V/0.1 A |
Applicable connector
(cable side) |
Phoenix Contact MVSTBR2, 5/4-ST-5, 08 |
|
Digital interface |
RS-232C / CAN(option) |
|
Other function |
|
Moving average |
2 to 720 times |
|
Deceleration calculation |
Selection of time or cycle
Time : 1 to 1200 ms
Cycle : 1.5/3/5/8/16 |
|
Trigger assist |
Automatic setting of trigger level employed until pulse detection |
|
Resume function |
Preserving condition values even while power is off. |
|
Condition memory |
Up to 5 types of condition memory can be saved. |
|
General specification |
|
Power requirement |
DC 9 to 28 V, 12 VA or less
·AC adapter(AC100-240 V, 36 VA or less)
·Input cable with fuse clips on both ends(option) |
|
Outer dimensions |
170(W)× 49(H)× 120(D) mm |
|
Weight |
Approx. 700 g |
|
Operating temperature range |
0 to 50 ℃ *2 |
|
Operating humidity range |
5 to 85 %(with no condensation) |
|
CE marking |
Low Voltage Directive: 2014/35/EUEN61010-1 class1 (when AC adapter is used.)
EMC Directive : 2014/30/EUEN61326-1 class1 Industrial Environment
RoHS Directive : 2011/65/EUEN50581 |
|
FCC |
47 CFR 15 Subpart B Class A |
|
Accessory |
·Rubber foot x 4
·AC adapter (100-240 V) for DC16 V
·Instruction Manual × 1 |