Linear Gauge Sensors Onosoki GS-1713A, GS-1730A, GS-1813A, GS-1830A

Sản phầm nổi bật

Trusco

Tsubaki

OTSUKA

Ebara

Atago

Tin tức mới nhất

Vì sao khách hàng chọn mua máy nén khí Nhật bãi ?Tại sao máy nén khí trục vít Buma tạo được lòng tin với người tiêu dùng?Một vài sự cố sử dụng biến tần trong máy nén khí Lựa chọn máy nén khí Nhật Bản

Linear Gauge Sensors Onosoki GS-1713A, GS-1730A, GS-1813A, GS-1830A

Mã sản phẩm: GS-1713A, GS-1730A, GS-1813A, GS-1830A

Tình trạng:

Linear Gauge Sensors Onosoki GS-1713A, GS-1730A, GS-1813A, GS-1830A

Liên hệ

Thông tin sản phẩm hướng dẫn đặt hàng & vận chuyển

Specifications

Model name Item	GS-1713A	GS-1730A	GS-1813A	GS-1830A
Measurement range	13 mm	30 mm	13 mm	30 mm
Resolution	10 μm		1 μm
Accuracy (at 20 °C)	3 μm	3 μm	2 μm	3 μm
Maximum spindle velocity^*1	1(4) m/s		0.3(1.2) m/s
Measurement force(downward)^*2	1.3 N or less	1.9 N or less	1.3 N or less	1.9 N or less
Number of sliding times (proven in our endurance test)	6.5 million times or more
Protection class (not including connector part)	IP64
Stem diameter	Ø15 mm^+0-0.009
Power supply	4.5 to 5.5 VDC
Power consumption (5 VDC)	120 mA or less
Signal output (5 VDC)	Two-phase square wave, phase difference: 90° ± 20° Output voltage Hi:4.5 V or more / Lo:0.4 V or less
Output impedance	Approx. 22 Ω
Vibration resistance (when the power is off) ^*3	98 m/s² in each of the three axial directions (75 minutes per each), 10 cycles of 10 Hz to150 Hz sweeping
Shock resistance (when the power is off)^*3	980 m/s² in each of direction for each of three axex, three times for each of ±X,Y and Z directions, sine half-wave, pulse duration 6 ms
Operating temperature range	0 to +40 °C
Storage temperature range	-10 to +55 °C
Cable length	Approx. 1.9 m
Weight (including cable, connector)	Approx. 250 g	Approx. 310 g	Approx. 250 g	Approx. 310 g
Accessories	Instruction manual, spanner

*1. When used with Ono Sokki's Gauge Counter. The values within parentheses () is the maximum spindle velocity used with the DG-4140/DG-4190/DG-5100/DG-3000.
*2. An attachment may not return completely if it is facing upwards.

*3 Vibration/shock resistance values described in above are not guaranteed during measurement operation.

• Disconnected or modified signal cable is not applicable to CE marking.

NOTE:Please check an attaching portion (material, grounding etc.) before you install the New GS series. If the New GS series is installed in a metallic portion that is not grounded, it might cause blowout of a fuse or cable damage because of a potential difference that might be produced between a counter side chassis and a sensor side chassis.

Về trang trước

Gửi emmail In trang