Ono sokki Elevator Speedometer EC-2100

Sản phầm nổi bật

Trusco

Tsubaki

OTSUKA

Ebara

Atago

Tin tức mới nhất

Vì sao khách hàng chọn mua máy nén khí Nhật bãi ?Tại sao máy nén khí trục vít Buma tạo được lòng tin với người tiêu dùng?Một vài sự cố sử dụng biến tần trong máy nén khí Lựa chọn máy nén khí Nhật Bản

Ono sokki Elevator Speedometer EC-2100

Mã sản phẩm: EC-2100

Tình trạng:

Ono sokki Elevator Speedometer EC-2100

Liên hệ

Thông tin sản phẩm hướng dẫn đặt hàng & vận chuyển

The EC-2100 is a compact, light weight and battery-operated handheld speedometer designed for use in elevator adjustment, maintenance and inspection. With a wide measurement range and high speed calculation, speed and rotation of a high speed elevator can be measured.

It enables easy and accurate measurement only by pressing the circumferential ring lightly to an elevator pulley or a handrail of an elevator. Measured value can be easily read on the red LCD even in a dark place. The operator can do an inspection alone by fixing the EC-2100 main unit by a jig or using the EC-0201 external detector (option).

As well as the buttons on the main unit, the measurement values can be held by the external contact signal. The each instantaneous value is displayed on the main unit. It supports more safety work without worrying about the displayed values.

Distance measurement is available by the EC-0202 (option). It measures moving distance within the specified time. Moreover by adding the EC-0202 (option) and the EC-0203 (option), the EC-2100 can measure actual moving distance of an escalator after emergency stop operation.

Overview Specifications

EC-2100 Elevator Speedometer

Measurement section
Measurement method	Contact type
Measurement range	Speed^1: 0.1 to 2,000.0 (m/min) or 1 to 6,500.0(f/min) Rotation speed: 1 to 20,000 (r/min) Distance (sold separately)^1: 0 to ±999 (mm) or 0 to 3.280 (feet) *Distance measurement up to ±5000 mm or 9.999 feet is available. However, measurement values more than ±999 mm or ±3.280 feet is not guaranteed.
Measurement accuracy	±1 count
Measurement time	10 ms
Display	5-digit red LED × 2
Display update time	100 ms
Resolution^*1	Speed: 0.1 (m/min) or 0.328 (f/min)^*2 , rotation speed:0.1 (r/min), distance (sold separately): 1 (mm) or 0.001 (feet) nSpeed and rotation speed: 10 or more of averaging times
Measurement unit^*1	Speed: m/min or f/min, rotation speed: r/min, distance: mm or feet (distance: option)
Auto power off function	A delay of three minutes after last operation automatically lets the power off.
Data hold function	Data hold of each channel (CH 1, CH 2, Max value)
Averaging function	1 to 200 times (optionally setup)
Memory function	Up to ten measurement results can be stored to the main unit.
Analog output section
Output signal	Instantaneous value (output after averaging processing)
Voltage range	0 to 1 V/0 to F.S.
Conversion method	10-bit D/A conversion
Linearity	±1％ F.S.
Output update time	10 ms
Output connector	φ2.5 mm pin-jack
Pulse output section
Output method	Transistor output (open collector)
Voltage withstanding	14 V
Current	20 mA or less
The number of pulses	600 pulses / rotation
Logic	Negative logic
Pulse width	Approx. 0.5 to 1.2 μs
Output connector	φ2.5 mm pin-jack
Detector section
The number of generated pulses	150 pulses/ rotation, slit reflection method
Light source	Infrared-emitting diode
Light receiving element	Photodiode
Allowable shaft load	Radial:5kg, thrust:5kg
Bearing life	2×10⁷ r/min･h (at the time of maximum load within the specification)
General specification
Power supply	Type AA battery x 3 pieces
Battery life	15 hours or more (continuous using at room temperature)
Current consumption	100mA max. (power voltage 4.5V)
Operating temperature range	0 to 45 °C
Storage temperature range	-10 to 60 °C
Outer dimensions	60(W)×162(L)×38(D)mm (same as the EC-900)
Weight	Approx. 423 g (including batteries, not including the circumferential ring)
Accessories	External hold signal cable (1.4m) EC-0922 x 1 set (2 pieces) Carrying case EC-0925 x 1 piece Hexagonal wrench (opposite side:1.5mm) x 1 piece Type AA battery x 3 pieces

Note: When using the EC-2100, optional circumferential ring (KS-400, 500, 0800) or optional rotating contact tip (KS-300, EC-0924) is required.

*1: The measurement unit is selectable from mm (m/min) or feet (f/min). Please specify the unit at the time of order.
*2: Displaying to the first decimal point.

Quick operation procedure "How to use the EC-2100" (PDF)

Option

EC-0201 External detector

External detector for the EC-2100 Elevator speedometer. Remote operation using signal cable (EC-0921, standard accessory) provides safety measurement.

*The measurement operations such as power ON and unit selection are performed on the main unit.

Detection section
The number of generated pulsed	150 pulse/rotation slit reflection method
Light source	Infrared-emitting diode
Light receiving element	Photodiode
Allowable shaft load	Radial:5 kg, thrust: 5 kg
Bearing life	2×10⁷ r/min・h (at the time of maximum load within the specification)
General specification
Power supply	Supplied from the EC-2100 (uses the EC-0921 external signal cable for the EC-0201)
Operating temperature range	0 to 45 °C
Storage temperature range	-10 to 60 °C
Outer dimensions	60(W)×76(L)×38(D)mm with jig mounting hole (4-M4 depth 8) (same as the EC-091)
weight	Approx. 214 g (including batteries, not including circumferential ring)
Accessories	External detector signal cable (5 m): EC-0921 x 1 piece (connection for the EC-2100 and the EC-0201)