Bộ chuyển dữ liệu Magnescale Interface MG-40

Sản phầm nổi bật

Trusco

Tsubaki

OTSUKA

Ebara

Atago

Tin tức mới nhất

Vì sao khách hàng chọn mua máy nén khí Nhật bãi ?Tại sao máy nén khí trục vít Buma tạo được lòng tin với người tiêu dùng?Một vài sự cố sử dụng biến tần trong máy nén khí Lựa chọn máy nén khí Nhật Bản

Bộ chuyển dữ liệu Magnescale Interface MG-40

Mã sản phẩm: MG-40

Tình trạng:

Bộ chuyển dữ liệu Magnescale Interface MG-40

Liên hệ

Thông tin sản phẩm hướng dẫn đặt hàng & vận chuyển

Features

MG40 series, new measurement system integrates the primary functions of a counter into the gauge itself to a high degree. The MG40 series does not have to count analog outputs or AB phase outputs of the gauge and acquires positional information directly via full digital communication. The theoretical response speed is 20 times faster than the response speed of our previous models. Miscounts, caused by external noise, are eliminated and the system is capable of instantly recovering from a communication error by way of re-reads.

Ethernet and CC-Link models are available
High-speed and highly reliable communication shortens cycle times
- High-speed communication via Ethernet
- Communication error detection
- High-speed RISC processor dedicated to communication
- Our proprietary high-speed processor for multi-axis data processing
- Newly developed ASIC
Quick and simple wiring connections
- Connection via a hub
- PLC connections
- Acquiring individual gauge information
- DIN rail mount and frontal connections
Maximized system efficiency
- On the path to a revolution in quality
- High-speed measurements enable shorter cycle time
- Lower overall system costs

Specifications

Specifications
Item		Conditions	Description					Remarks
Magnescale reserves the right to change product specifications without prior notice.
No. of connectable measuring units		Entire system	1 to 100 units (Connection disabled aft er connection of 101st unit.)					Up to 24 connected MG42 hub units
		MG41main unit	0～4units
		MG42hub unit	0～4units
Connectable measuring units			DK800A/DK800B series, DK10, DK25, DK50, DK100, DK110, DK155, DK205
Connection cable length			Between MG41 main unit and MG42 hub unit Total cable length from MG41 main unit: Maximum 30 m(Maximum current: 4 A or less)
Resolution			Settable output data resolution and display resolution
	Measuring unitsResolution(Input resolution)	0.1μm	0.1μm	0.5μm	1μm	5μm	10μm
	Measuring unitsResolution(Input resolution)	0.5μm	-	0.5μm	1μm	5μm	10μm
Measuring unit data import capacity		data transfer10Mbps	Maximum 10					The data for one axis is counted as one data.
Peak hold function			Calculation of maximum value
			Peak value is not updated during pause.
			Output and display data are not updated during latching (internal data is updated)
			Recalculation of peak value is started by start function.
Output data		Single axis	Current value
Output data		Addition and subtraction	Current value					Single axis calculation of an addition / subtraction axis is not possible(for preventing inconsistencies in calculation).
Conparetor function			Data for each axis (single axis
	Comparator setting values		2values		4values	8values	16values
	No. of setting value groups		16groups		8groups	4groups	2groups
Ethernet			100Base-T (compliant with IEEE 802.3) 100 Mbps/10 Mbps/1 Mpbs (Auto-negotiation) Command input
Reset function			Current value for each axis is reset (by command).
Preset function			Value is preset to the current value of each axis (by command).
Datum point setting function			Datum point of each axis can be set (by command).					When master calibration function is not used
Reference point function			Reference point can be used to relocate the datum point of each axis (by command).					When master calibration function is not used
Master calibration function			Reference point can be used to perform master calibration for each axis (by command).
Measuring unit product information			The product information of the connected measuring unit can be acquired.
Command/setting enabled or disabled for each communication line						Ethernet	CC-Link
			Command	Reset function		○	○
				Preset function		○	○
				Datum point setting function		○	○	When master calibration function is not used
				Reference point function		○	○	When master calibration function is not used
				Master calibration function		○	○
				Comparator value setting		○	○
				Comparator group number setting		○	○
				Start		○	○
				Pause		○	○
				Latch		○	○
			Data output	Current value・Peak value( All axis)		○	×
				Current value・Peak value( each unit)		○	○
				Comparator result		○	○
				Alarm( data transfer・Measuring units)		○	○
				Soft ware version		○	○
				Measuring unit product information		○	○
			Comparator result	Input resolution		○	○
				Display・Resolution		○	○
				Axis addition		○	○
				Comparator mode (2, 4, 8, or 16 values in 1 group)		○	○
Power supplyPower supply voltage		Terminal input	DC12～24V(11～26.4V)					Use a power supply with a current that is 4 A or higher. (Recommended: +24 V) (for every six MG42 hub units)
Power consumption		Note the connection conditions.	System total: Max. current 4A
			When the maximum current is exceeded

Operating temperature/humidity			0～+50℃(non condensing)
Storage temperature/humidity			-10～+60℃(20～90%RH)
Mass			MG41:300g MG42:250g